INTEX air bed use and maintenance:
< 1 >, air bed after buying back (winter in the of China should pay attention to in the indoor 24 hours and then inflatable: wait until the temperature of the products with indoor temperature consistent. Just more reasonable durability. Otherwise easy to have materials
Crisp, product to burst.) the first eight hours after finish filling gas (best 12 hours) just can use, because air bed, take and seam in abrasive-cloth adhered need a buffer process; New bed use two days before, as far as possible don't enough gas.
< 2 >, a filling the air, air bed will some slack, this is normal phenomenon, air bed materials some flexibility, filling the air grew up after some become soft, just feel lax, as long as the inflatable reach the expected effect again line, but don't cheer too full.
< 3 >, one person use can be enough gas, two people use to put off some gas; season
Conversion section temperature rise, the bed gas inside the inflation, pay attention to put gas.
< 4 >, when the temperature drops, lathe bed will become soft, pay attention to fill gas; Any inflatable products (including tires) will be natural leakage, this is normal phenomenon, pay attention to fill gas regularly.
Season changeover temperature, air supplies gas inside the inflation, pay attention to drop a breath.
< 5 >, any time cannot inflatable with (especially summer), or in bed with excess load will pull fracture, causing the surface of bed bulge, this kind of situation will be unable to repair.
< 6 >, guarantee, making the bed the ground or no nails or thorn, blue objects.
< 7 >, inflatable products, if use in the wild, please do not inflatable too full (8 to 9 into BaoManDu is preferred). In the wild, pay attention to clean out the use of ground of the debris ( objects, such as small stone), the better to put a layer of things, such as carpet, cartons, and so on. People in the air on the things are turning, will stimulate the rotation of the inflatable products, the bottom of the materials will follow the ground friction, air too full, very easy to wear materials, makes the material damage and cause leakage phenomenon.
< 8 >, all inflatable products can't stand on it jump. Because a jump with bed face very small steps, the foot to the impact of the bed is very big, very easy to cause the inflatable supplies of pull with (a column) damage. The damage is not way to repair!
< 9 >, if used in water, ensure suede up, children in adult care should be used.
INTEX air bed use basic common sense:
First, I'm full of gas, the second day, the feeling a bit loose, is this normal?
A: new inflatable products, started using, inflated materials received in the pressure of the pressure, will have a bit of stretch, twisted will a little volume. This time you will feel like a bit slow leak is product of appearance, this is to belong to normal. Use 2 ~ 3 days material won't stretch, this time complement the gas can be used normally. If a flat is more, that you have to check whether the lid air cover. Pillar valves three layers device:
The first layer: the biggest a layer of the lid, both sides have white to the arrow within. This layer is used to put the lid of the gas, you hear in the left or right side "kaka" two empress, said already lock.
The second floor: have the lock and closure of the sign. The direction of arrow, twist to the position of the spring tighten will do.
The third floor: the top layer of the, used for air use, is through the short tape pull drawn, thumb in, make sure the end).
Second, inflatable bed will not leak? If do not take care firm is broken? How to effectively find out in a flat?
A: Intex inflatable bed in before they leave the factory had passed through the very strict quality checks, so you don't have to worry about its will leak. Intex inflatable bed material not easy firm break, when use, Suggestions on the shop on sheet, quilt or mat, increase comfort, more increase protection. If all carelessly prick, can be used with the small patches bed presented according to the instructions to repair, simple and convenient.
!!!!!!! That how to check the position of the bed air leak?
A: inspection air bed a flat position is required for a very careful work, according to the following way slowly inspection:
1), first check air bed sewing by whether edge crack;
2), check seam meet edge part and bed between body (i.e. 6 mm to 8 mm place) the presence of a tear phenomenon;
3), and then will face and ears near the gas mouth feel, check the gas leak is mouth part; If it is not the problem, it according to the number of holes air bed at a check. Air bed is usually eight hole one row, check out a row preclude a row:
4), check the underside, because the most easily by the ground floor of the objects or on bedstead MuCi pierced the break, according to the order from left to right, choose the most left a row of hole, and from the most left a hole began to check, and with each hole for the center around the hole to spread, first look at the different place without burnish, to see whether the place is ceng fold seal break, found to have burnish different or have been ceng, folding of the places, face and ears close to feel, if you find a trace of the wind from a needle come out, and as long as on drop a repair glue.
5), according to article 4 methods to check suede, suede and key or other things of the firm may;
6), check the profile, and by from left to right order, a piece of an area inspection. Side also is key, in air bed move, is likely to be on the wall of the desk nails or the MuCi firm broken; The inspection method is the most convenient and effective and most the method of save trouble, just start may have to spend half an hour, skilled in the later, often a few minutes can be found out.
Three, the received product size than product introduction why and products of color box with the slightly smaller size?
Answer: 1. The factory are the size of inflatable products 100% mark, but charging products normal can only 7 to 8 minutes full charge, because the charging products 100% easy to cause the bulge filling phenomenon, beat the general situation is can't repair
2. Inflatable products of the materials are certain for sex, new purchase products will be less than size online (box) mark on size, use after period of time, the material will have for sex, product size relative also increase some.
!!!!!!! If size have very strict requirements for the friends of the trouble in the first before buying questions we , lest produce misunderstanding after purchase
Four, the honeycomb < pillar > type and tape pull < strander > type structure have what differentiation?
A: cellular than pull belt type more advanced, more comfortable. Some higher content of technology.
Five, inflatable bed in the summer and winter how to use?
A: the air permeability of relative bed than poor effect, but the problem is very good solution: covered with a layer of quilt. Used in the summer, just above on the shop a sheet, put on a "mahjong" bamboo mat went, the whole summer, you can debate to sleep on the surface that cool cool cozy feeling; Use in winter, it is on the shop on a thicker or cotton quilt, and to increase the heat preservation and permeability, also like to sleep in the warm MianDui.
Six, inflatable bed can clean?
A: can, not the bottom and sides of suede, as long as the wet with soap and water with the cloth to wipe clean can be easily; If suede is stained, it need soap water clean thoroughly, and make its natural drying, don't use the blow blow-dry suede, cannot use the washing machine air bed, cannot use day took water chemicals, such as washing powder or any other polishing powder.
Seven, how to fix the damage of the air bed?
Answer: to teach you repair inflatable bed: the following A-B-C-D
A, repair A needle:
If you of the air bed with needle or MuCi taken one or more small needle, is the most easy to repair the:
1, the bed put gas back cover spirit mouth, reduce the gas flow in the bed;
2, will repair the glue bag, take it out of place in a needle drop a drop of glue line;
3 if a needle, bigger, is take a toothpick, until a toothpick pointed Jiao point glue, the broken needle with the inside, then use the needle mouth covered with glue can;
4, repair finish, and so on four hours before charging.
B, through the mouth or hot repair bad mouth:
If you of the air bed with knife cut or burnt is a cut, please don't panic, according to the following order, it can be mended:
1, the bed put gas back cover spirit mouth, reduce the gas flow in the bed;
2, in repairing bags find patch material, cut off a piece of, need to be broken seam covered enough;
3, plastic coated in the destroyed place, pressure on the patch, the patch with glue of edge crack glue;
4, with pressure, to ensure that no glue face aperture, with smooth, heavy objects will hold its pressure;
Five, eight hours after the inflatable, repair the finish.
C, suede repair:
1, careful cleaning repair area;
2, after dry, take out a patch cut in on the cover destroyed, allow around a bit more;
3 in patch and damaged surface, coated with glue, glue with the patch of edge crack glue, to ensure the sealing completely;
4, with smooth, heavy objects will hold its pressure;
5, with heavy pressure, the pressure to 24 hours later again the inflatable, repair the finish.
D, other matters:
1, remember that don't inflate too full (especially in summer), not in bed for too violent campaign, otherwise in the bed, with will overload and rupture, causing the surface of bed bulge beyond repair, can only be scrapped.
2, repair glue is with chemicals, and don't contact with eyes or swallowed.